Skip to content

Capacitor Lists for Home Consoles and Atari Lynx

Electrolytic capacitors age: they dry out or leak. The result is audio noise and distortion, video problems, instability and, eventually, consoles that no longer start at all. On this page you will find all known electrolytic capacitors for each console, per board revision, grouped by value and sorted from smallest to largest capacitance.

To learn how to replace the capacitors (SMD and through-hole), see our guide Replacing capacitors (recap).

The data has been compiled from multiple sources, including original manufacturer schematics and service manuals, RetroRewind, SMS Power!, World of Jani, PCEngineFans, RetroTechCollection, Console5, iKod, Spectrum for Everyone, Retroleum, Arcade Projects, 68kMLA and various community repair guides and forum threads.

The Super Nintendo Entertainment System (SNES, or Super Famicom in Japan) was released in Japan in November 1990 and in North America in August 1991. It has a 3.58 MHz Ricoh 65C816 16-bit CPU, custom graphics chips (PPU1 and PPU2) and the SPC700-based audio DSP. It went through numerous board revisions during its production life: the early multi-chip boards, the later 1CHIP boards that consolidated the CPUs, and the SHVC-CPU-01 Japanese launch board with its detachable sound module. Aging electrolytic capacitors in the SNES can cause audio noise and video signal degradation.

SHVC-CPU-01 is the original Japanese Super Famicom launch board from 1990. It is the largest of all SNES boards and unique for its detachable sound module, which holds virtually all audio hardware (S-SMP, S-DSP, sound RAM, DAC and amplifier) on a separate sub-board. The AV multi-out on this revision does not support S-Video or RGB; that was added in later revisions.

Designators Value Voltage Notes
(1×) C62 2.2uf 50v SMD; CIC / reset circuit cap
(3×) C61, C65, C66 10uf 16v SMD; power/video decoupling
(2×) C63, C64 33uf 25v SMD; power rail decoupling
(2×) C50, C51 47uf 10v SMD; bulk decoupling
(4×) C57, C58, C59, C60 100uf 6v SMD; audio output filter — common failure point — audio static/distortion; upgrade to 10V recommended
(1×) C67 1000uf 25v THT; main power filter cap; use 105°C rated
Designators Value Voltage Notes
(1×) C62 2.2uf 50v SMD; F411 CIC / reset circuit cap
(3×) C61, C65, C66 10uf 16v SMD; power/video decoupling
(2×) C63, C64 33uf 25v SMD; power rail decoupling
(1×) C73 47uf 16v SMD; bulk decoupling
(2×) C57, C59 220uf 6.3v THT; video encoder output filter (VO/YO); upgrade to 10V recommended
(1×) C67 1000uf 25v THT; main power filter cap; use 105°C rated

SNS-CPU-RGB-01, SNS-CPU-RGB-02, SNS-CPU-APU-01

Section titled “SNS-CPU-RGB-01, SNS-CPU-RGB-02, SNS-CPU-APU-01”
Designators Value Voltage Notes
(1×) C9 2.2uf 50v SMD; CIC / reset circuit cap
(2×) C12, C13 10uf 16v SMD; power/video decoupling
(3×) C14, C16, C17 33uf 25v SMD; power rail decoupling
(1×) C15 47uf 16v SMD; bulk decoupling
(2×) C18, C19 220uf 6.3v THT; video encoder output filter (VO/YO); upgrade to 10V recommended
(1×) C58 1000uf 25v THT; main power filter cap; use 105°C rated

SNS-CPU-1CHIP-01, SNS-CPU-1CHIP-02, SNS-CPU-1CHIP-03

Section titled “SNS-CPU-1CHIP-01, SNS-CPU-1CHIP-02, SNS-CPU-1CHIP-03”
Designators Value Voltage Notes
(1×) C9 2.2uf 50v SMD; CIC / reset circuit cap
(2×) C12, C13 10uf 16v SMD; power/video decoupling
(3×) C14, C16, C17 33uf 25v SMD; power rail decoupling
(1×) C15 47uf 16v SMD; bulk decoupling
(2×) C18, C19 220uf 6.3v THT; video encoder output filter (VO/YO); upgrade to 10V recommended
(1×) C58 1000uf 25v THT; main power filter cap; use 105°C rated
Designators Value Voltage Notes
(1×) C9 2.2uf 50v SMD; CIC / reset circuit cap
(2×) C58, C59 10uf 16v SMD; power/video decoupling
(3×) C14, C16, C17 33uf 25v SMD; power rail decoupling
(1×) C15 47uf 16v SMD; bulk decoupling
(1×) C60 220uf 6.3v THT; video encoder output filter (VO/YO); upgrade to 10V recommended
(1×) C52 1000uf 25v THT; main power filter cap; use 105°C rated
Designators Value Voltage Notes
(1×) C62 2.2uF 50v SMD; CIC / reset circuit cap
(1×) C59 10uF 25v SMD; power circuit cap; replace with bipolar; Nintendo revised to bipolar in SNSP-CPU-02
(4×) C60, C61, C65, C66 10uF 50v SMD; power/video decoupling
(2×) C63, C64 33uF 25v SMD; power rail decoupling
(1×) C73 47uF 16v SMD; bulk decoupling
(1×) C67 2200uF 25V THT; main power filter cap; use 105°C rated
Designators Value Voltage Notes
(1×) C62 2.2uF 50v SMD; CIC / reset circuit cap
(1×) C59 10uF 25v SMD; power circuit cap; bipolar (Nintendo revised to bipolar in SNSP-CPU-02)
(4×) C60, C61, C65, C66 10uF 50v SMD; power/video decoupling
(2×) C63, C64 33uF 25v SMD; power rail decoupling
(1×) C73 47uF 16v SMD; bulk decoupling
(1×) C67 2200uF 25V THT; main power filter cap; use 105°C rated
Designators Value Voltage Notes
(1×) C9 2.2uF 50v SMD; CIC / reset circuit cap
(2×) C12, C13 10uF 16v SMD; power/video decoupling
(1×) C59 10uF 25v SMD; power circuit cap; bipolar (Nintendo revised to bipolar in SNSP-CPU-02)
(1×) C71 10uF 50v SMD; power/video decoupling
(3×) C14, C16, C17 33uF 25v SMD; power rail decoupling
(1×) C15 47uF 16v SMD; bulk decoupling
(2×) C18, C19 220uF 6.3v THT; video encoder output filter (VO/YO); upgrade to 10V recommended
(1×) C72 2200uF 25V THT; main power filter cap; use 105°C rated

The Sega Master System is an 8-bit third-generation console, released in North America in 1986 and in Europe and Brazil in 1987. It competed directly with the NES and was sold in multiple hardware revisions for NTSC and PAL markets. The electrolytic capacitors throughout the Master System are prone to leaking and drying out with age, leading to degraded audio, video noise and general instability.

The original 1986 North American Master System mainboard, found in launch units and early production runs sold in North America.

Designators Value Voltage Notes
(7×) CA1, C1, C49, C119, C120, C121, C131 10uF 16v THT
(3×) C122, C123, C124 47uF 10v THT
(6×) CA20, C4, C20, C22, C25, C28 100uF 10v THT

837-6405 / 171-5532 & 837-6629: SEGA M4, POWERBASE/NTSC

Section titled “837-6405 / 171-5532 & 837-6629: SEGA M4, POWERBASE/NTSC”

Mid-production NTSC board revisions sharing the same capacitor layout. The main change from the 837-6067 is a different voltage rating on several capacitors.

Designators Value Voltage Notes
(1×) C37 1uF 50v THT
(6×) CA1, C49, C119, C120, C121, C131 10uF 10v THT
(3×) C122, C123, C124 47uF 10v THT
(4×) C4, C20, C28, C51 100uF 10v THT
(1×) C1 100uF 16v THT

837-6148: IC BOARD M4J MAIN (Japanese market)

Section titled “837-6148: IC BOARD M4J MAIN (Japanese market)”

The Japanese domestic mainboard, sold as the Sega Master System in Japan. It uses a significantly different capacitor selection compared to the export boards, including bipolar electrolytic capacitors in the audio circuit.

Designators Value Voltage Notes
(7×) C22, C24, C26, C27, C28, C29, C46 2.2uF 50v THT
(5×) C30, C47, C131, CCP1, CCP2 10uF 16v THT
(3×) C122, C123, C124 47uF 10v THT
(7×) C4, C20, C41, C42, C43, C44, C45 100uF 10v THT
(1×) C1 220uF 10v THT

The compact NTSC Master System II board, used in the later Master System II sold in North America and some export markets.

Designators Value Voltage Notes
(1×) C62 1uF 50v THT
(2×) C2, C73 10uF 16v THT
(6×) CE 10uF 16v SMD; 6 caps on this board share the CE designator
(1×) C1 47uF 10v THT
(3×) C53, C54, C71 100uF 10v THT
(1×) C50 100uF 16v THT

The original compact PAL Master System II board, used in European and Australian units. This revision uses individually numbered CE designators rather than the shared CE label seen on some other boards.

Designators Value Voltage Notes
(1×) C31 1uF 50v THT
(9×) CE1, CE2, CE3, CE4, CE5, CE6, CP, C18, C32 10uF 16v Mixed — CE1–CE6 and CP are SMD; C18 and C32 are THT
(1×) C44 47uF 10v THT
(3×) C38, C42, C43 100uF 10v THT
(1×) C41 100uF 16v THT

A later compact PAL revision with expanded memory support. Notable for a 330uF capacitor not found on any other revision.

Designators Value Voltage Notes
(1×) C31 1uF 50v THT
(1×) C18 10uF 16v THT
(6×) CE 10uF 16v SMD; 6 caps on this board share the CE designator
(1×) C44 47uF 10v THT
(5×) C38, C41, C42, C43, C59 100uF 16v THT
(1×) C32 330uF 16v THT

The RGB variant of the VA1 PAL board, fitted in units with RGB output. Uses individually numbered CE designators instead of the shared CE label.

Designators Value Voltage Notes
(7×) C2, CE1, CE2, CE3, CE4, CE5, CE6 10uF 16v Mixed — CE1–CE6 are SMD; C2 is THT
(1×) C1 47uF 10v THT
(2×) C53, C54 100uF 10v THT
(1×) C50 100uF 16v THT

The final PAL Master System board revision, used in late-production European units.

Designators Value Voltage Notes
(1×) C62 1uF 50v THT
(4×) C1, C70, C71, CP 10uF 16v THT
(6×) CE 10uF 16v SMD; Up to 6 caps marked CE may be present on this board
(3×) C9, C10, C11 47uF 16v THT
(4×) C53, C54, C63, C72 100uF 10v THT
(1×) C50 100uF 16v THT

The Power Base Converter (North America) and Mega Adaptor (Japan/Europe) let you play Master System cartridges and cards on the Sega Mega Drive / Genesis.

Designators Value Voltage Notes
(1×) C4 1uF 50v THT; PBC version only
(2×) C1, C2 47uF 16v THT

The Sega Mega Drive 2 (Genesis 2 in North America) is a cost-reduced redesign of the original Mega Drive, released in 1993, with a smaller form factor, no headphone jack or front volume slider, and a simplified PCB. It went through several board revisions (VA2.3, VA3, VA4) with significant internal changes, including the introduction of an ASIC and eventually the Genesis-On-A-Chip (GOAC) design that combines most of the system logic in a single IC. Electrolytic capacitors throughout the Mega Drive 2 are prone to age-related failure, causing audio noise and video artifacts, and the later GOAC-based VA4 revision in particular has noticeably worse audio.

Designators Value Voltage Notes
(11×) CE1, CE2, CE3, CE4, CE5, CE6, CE7, CE8, CE9, CE10, CE11 10uF 16v
(1×) CE12 220uF 6.3v
(9×) CE14, CE15, CE20, CE21, CE22, CE29, CE30, CE31, CE32 10uF 16v
(7×) CE18, CE19, CE24, CE25, CE26, CE27, CE28 47uF 10v
(2×) CE17, CE23 100uF 10v
(1×) CE16 220uF 16v
Designators Value Voltage Notes
(11×) CE1, CE2, CE3, CE4, CE5, CE6, CE7, CE8, CE9, CE10, CE11 10uF 16v
(1×) CE12 220uF 6.3v
(1×) CE14 10uF 16v CXA1145/KA2195D boards
(1×) CE14 220uF 6.3v MB3514PF boards
(8×) CE15, CE20, CE21, CE22, CE29, CE30, CE31, CE32 10uF 16v
(7×) CE18, CE19, CE24, CE25, CE26, CE27, CE28 47uF 10v
(2×) CE17, CE23 100uF 10v
(1×) CE16 220uF 16v
Designators Value Voltage Notes
(1×) CE5 2.2uF 50v
(15×) CE1, CE2, CE3, CE4, CE6, CE8, CE11, CE13, CE14, CE20, CE21, CE29, CE30, CE31, CE32 10uF 16v
(1×) CE15 22uF 50v
(7×) CE18, CE19, CE24, CE25, CE26, CE27, CE28 47uF 10v
(4×) CE9, CE10, CE17, CE23 100uF 10v
(1×) CE12 220uF 6.3v
(1×) CE16 220uF 16v
Designators Value Voltage Notes
(1×) CE1 2.2uF 50v
(10×) CE5, CE6, CE7, CE11, CE14, CE20, CE21, CE22, CE29, CE30 10uF 16v CE14: (Type A and B PCBs only, CE14 is empty on Type C PCBs)
(1×) CE2 22uF 50v
(5×) CE24, CE25, CE26, CE27, CE28 47uF 10v
(4×) CE3, CE4, CE17, CE23 100uF 10v
(1×) CE12 220uF 6.3v
(1×) CE16 220uF 16v
Designators Value Voltage Notes
(1×) CE16 2.2uF 50v
(6×) CE5, CE6, CE11, CE12, CE13, CE17 10uF 16v
(1×) CE18 22uF 16v
(9×) CE1, CE2, CE3, CE4, CE9, CE21, CE22, CE23, CE24 47uF 10v
(4×) CE7, CE14, CE15, CE20 100uF 10v
(1×) CE8 220uF 6.3v
(1×) CE19 220uF 16v

The Sega Dreamcast is a sixth-generation console, released in Japan in November 1998 and in North America in September 1999, and the last console Sega released as a hardware manufacturer. It has a Hitachi SH-4 CPU, a PowerVR2 GPU and a proprietary GD-ROM drive, and was known for its built-in modem and online gaming. Electrolytic capacitors on the Dreamcast mainboard, especially around power regulation and audio, are known to leak or fail with age, causing audio distortion, startup failures and GD-ROM read errors.

The VA0 is the rarest and earliest Dreamcast revision, found mainly in early Japanese units. You can identify it by its distinctive metal fan cowl (heat pipe cooling). The VA0 uses 5V BIOS and flash chips (which can damage GDEMU optical drive emulators), draws more power than later revisions and has a visible heat pipe in the cooling assembly.

Designators Value Voltage Notes
(1×) CE309 4.7uF 35v SMD — common failure point — causes audio dropout
(2×) CE301, CE310 10uF 16v SMD
(2×) CE303, CE304 10uF 10v SMD — bipolar — audio coupling, use non-polarised capacitor
(2×) CE305, CE306 22uF 6.3v SMD
(1×) CE308 47uF 16v SMD
(1×) CE503 47uF 25v SMD
(1×) CE403 100uF 6.3v SMD
(1×) CE401 220uF 6.3v SMD

The VA1 is the most common Dreamcast revision and was produced for all regions for most of the console’s production life. Compared to the VA0 it uses 3.3V BIOS and flash chips and replaces the heat pipe with a simpler heatsink. It is the revision collectors run into most often. All VA0 and VA1 units support MIL-CD playback.

Designators Value Voltage Notes
(1×) CE309 4.7uF 35v SMD — common failure point — causes audio dropout
(3×) CE301, CE302, CE310 10uF 16v SMD
(2×) CE303, CE304 10uF 10v SMD — bipolar — audio coupling, use non-polarised capacitor
(2×) CE305, CE306 22uF 6.3v SMD
(2×) CE103, CE308 47uF 16v SMD
(1×) CE503 47uF 25v SMD
(1×) CE601 47uF 6.3v SMD
(1×) CE307 100uF 16v SMD
(1×) CE403 100uF 6.3v SMD
(1×) CE401 220uF 6.3v SMD
Designators Value Voltage Notes
(1×) CE309 4.7uF 35v SMD — common failure point — causes audio dropout
(3×) CE301, CE302, CE310 10uF 16v SMD
(2×) CE303, CE304 10uF 10v SMD — bipolar — audio coupling, use non-polarised capacitor
(2×) CE305, CE306 22uF 6.3v SMD
(2×) CE103, CE308 47uF 16v SMD
(1×) CE307 100uF 16v SMD
(1×) CE403 100uF 6.3v SMD
(1×) CE401 220uF 6.3v SMD
Designators Value Voltage Notes
(1×) CE1 47uF 16v SMD
Designators Value Voltage Notes
(1×) C2 47uF 6.3v SMD
(5×) C3, C10, C14, C17, C61 100uF 6.3v SMD
(2×) C20, C122 100uF 16v SMD
Designators Value Voltage Notes
(3×) C127, C203, C205 47uF 6.3v SMD
(5×) C10, C14, C17, C61, C511 100uF 6.3v SMD
(2×) C20, C509 100uF 16v SMD
Designators Value Voltage Notes
(3×) C127, C203, C205 47uF 6.3v SMD
(6×) C10, C14, C17, C61, C513, C520 100uF 6.3v SMD
(2×) C20, C509 100uF 16v SMD

Power supply: 171-7874A, 171-7874A-X1, 171-7874B

Section titled “Power supply: 171-7874A, 171-7874A-X1, 171-7874B”
Designators Value Voltage Notes
(1×) C10 47uF 35v THT
(1×) C3 100uF 200v THT
(1×) C16 220uF 25v THT
(1×) C22 470uF 10v THT
(1×) C13 1000uF 25v THT
(1×) C20 1500uF 6.3v THT
(2×) C17, C21 2200uF 10v THT

Power supply: 171-7874B-X2, 171-7962A, 171-7962A-X1, 171-7970A

Section titled “Power supply: 171-7874B-X2, 171-7962A, 171-7962A-X1, 171-7970A”
Designators Value Voltage Notes
(1×) C10 47uF 35v THT
(1×) C3 100uF 200v THT
(1×) C52 470uF 35v THT
(1×) C53 470uF 16v THT
(1×) C56 470uF 10v THT
(1×) C59 1000uF 10v THT
(1×) C54 2200uF 10v THT
(1×) C58 3300uF 10v THT

171-7960A, PWR UNIT PANA EU V01, ETXSE239E2C

Section titled “171-7960A, PWR UNIT PANA EU V01, ETXSE239E2C”
Designators Value Voltage Notes
(1×) C006 47uF 400v THT
(1×) C204 470uF 16v THT
(2×) C301, C302 1000uF 25v THT
(1×) C103 1200uF 10v THT
(2×) C101, C201 1800uF 16v THT

The Atari Lynx was released by Atari in September 1989. It was the first handheld with a color LCD and hardware sprite scaling, and uses a custom 65SC02-based CPU together with the Suzy sprite engine and the Mikey I/O chip. The electrolytic capacitors in the Lynx are known to degrade, causing dim or washed-out screens, distorted audio and power instability.

Typical Lynx I revision (Atari part number still to be confirmed)

Section titled “Typical Lynx I revision (Atari part number still to be confirmed)”
Designators Value Voltage Notes
(2×) C08, C75 1uf 50v THT — Signal coupling/decoupling; leakage can cause PCB trace damage
(2×) C19, C20 2.2uf 50v THT — Signal coupling/decoupling; leakage can cause PCB trace damage
(4×) C07, C25, C26, C42 10uf 6.3v THT — Local power decoupling; low voltage rating makes these prone to leakage and PCB damage
(2×) C23, C29 10uf 35v THT — Power supply filtering
(3×) C09, C10, C76 47uf 6.3v THT — Audio amplifier filtering; common failure — audio distortion or volume fade; prone to leakage
(1×) C38 100uf 35v THT — Power supply input filter; common failure — power instability
(1×) C11 220uf 6.3v THT — Power supply output filter; common failure — power instability, dim screen
(1×) C39 470uf 10v THT — Common failure — dim screen, power instability; main power bulk storage cap
Designators Value Voltage Notes
(2×) C8, C34 1uF 50v THT — Signal coupling/decoupling; leakage can cause PCB trace damage
(2×) C19, C20 2.2uF 50v THT — Signal coupling/decoupling; leakage can cause PCB trace damage
(4×) C7, C25, C26, C42 10uF 25v THT — Local power decoupling
(2×) C23, C29 10uF 35v THT — Power supply filtering
(2×) C9, C10 47uF 6.3v THT — Audio amplifier filtering; common failure — audio distortion or volume fade; prone to leakage
(1×) C38 100uF 25v THT — Power supply input filter; common failure — power instability
(1×) C11 220uF 6.3v THT — Power supply output filter; common failure — power instability, dim screen
(1×) C39 470uF 10v THT — Common failure — dim screen, power instability; main power bulk storage cap
Designators Value Voltage Notes
(4×) C16, C37, C47, C58 1uf 50v THT — Signal coupling/decoupling; leakage can cause PCB trace damage
(2×) C32, C33 2.2uf 50v THT — Signal coupling/decoupling; leakage can cause PCB trace damage
(4×) C03, C11, C27, C28 10uf 6.3v THT — Local power decoupling; low voltage rating makes these prone to leakage and PCB damage
(2×) C23, C25 10uf 35v THT — Power supply filtering
(4×) C14, C19, C53, C60 47uf 6.3v THT — Audio amplifier filtering; common failure — audio distortion or volume fade; prone to leakage
(1×) C39 100uf 35v THT — Power supply input filter; common failure — power instability
(2×) C21, C64 220uf 6.3v THT — Power supply output filter; common failure — power instability, dim screen
(1×) C41 470uf 10v THT — Common failure — dim screen, power instability; main power bulk storage cap

The Atari Lynx II (model PA2028) is the revised handheld released in 1991, with a more compact shell and better battery life than the original Lynx. It uses the same Mikey and Suzy custom chips on a redesigned PCB. Aging electrolytic capacitors cause audio distortion, display issues and power failures. The 470µF main power filter (C41) is the most common failure point.

Standard revision (C104471-001 Rev A / C104424 / C104342)

Section titled “Standard revision (C104471-001 Rev A / C104424 / C104342)”

The most common Lynx II board, found in roughly 80–90% of all units. Revisions C104471-001 Rev A, C104424-001 and C104342-001 share the same 20-capacitor layout.

Designators Value Voltage Notes
(4×) C16, C37, C47, C58 1uF 50v
(2×) C32, C33 2.2uF 50v Audio output coupling — NJM2073 stereo amplifier
(4×) C03, C11, C27, C28 10uF 6.3v
(2×) C23, C25 10uF 35v
(4×) C14, C19, C53, C60 47uF 6.3v
(1×) C39 100uF 35v
(2×) C21, C64 220uF 6.3v
(1×) C41 470uF 10v Main power filter — most common failure; causes no-power or shutdown

A rare early board revision, identifiable by the missing copper PCB shielding and flat-style potentiometers. C53, C58, C60 and C64 are omitted, 16 capacitors in total.

Designators Value Voltage Notes
(3×) C16, C37, C47 1uF 50v
(2×) C32, C33 2.2uF 50v Audio output coupling — NJM2073 stereo amplifier
(4×) C03, C11, C27, C28 10uF 6.3v
(2×) C23, C25 10uF 35v
(2×) C14, C19 47uF 6.3v
(1×) C39 100uF 35v
(1×) C21 220uF 6.3v
(1×) C41 470uF 10v Main power filter — most common failure; causes no-power or shutdown