Skip to content

Which IPS screen fits your Game Boy Color?

If you want to replace the screen of your Game Boy Color (CGB-001), an IPS or AMOLED kit takes the place of the original LCD. You get a high-contrast picture with vibrant colours and can adjust the brightness and retro pixel effects. The kits work for modding projects and for repairs when the original LCD is faulty.

On this page we compare the screen kits for the Game Boy Color from our shop. You will learn whether a laminated or a non-laminated kit suits your project, which shell you need, when you have to solder and which guide to follow for the installation.

The kits are made by Hispeedido and FunnyPlaying. Three of them are laminated, two are not laminated.

Q5 XL Laminated AMOLED Q10 XL Touch Q5 XL 2.45 HD OSD RetroPixel Laminated
Manufacturer Hispeedido Hispeedido Hispeedido Hispeedido FunnyPlaying
Design laminated laminated not laminated not laminated laminated
Screen technology IPS AMOLED IPS IPS IPS
Screen lens glass, bonded to the LCD glass, bonded to the screen glass lens with transparent artwork included black real glass lens included glass, bonded to the LCD
Viewing area 25 % larger than the original 25 % larger than the original 15 % larger than the original same as the original LCD 25 % larger than the original
Controls touch sensors, OSD menu touchscreen, OSD menu 2 touch sensors, OSD menu via buttons 2 touch sensors, OSD menu external touch sensor included, START + SELECT
Brightness levels 20 10 20 15 adjustable
Picture settings 8 colour modes, 5 retro pixel effects, frame blending, desaturation 8 colour modes, 4 retro pixel effects, frame blending 8 colour palettes, custom palettes possible, scanline effect 8 colour palettes, 3 retro pixel effects, frame blending display effects
Fits without modification Hispeedido, FunnyPlaying Hispeedido, FunnyPlaying RetroSix IPS Q5 shells (break out small tabs) original shell and RetroSix shells FunnyPlaying, Hispeedido
Original shell enlarge the screen window, remove the inner ridge enlarge the screen window, remove the inner ridge remove the ridge at the back, widen the screen window by 4 to 5 mm on each side (extensive modification) no cutting enlarge the screen window, remove the inner ridge
Soldering not needed. Optional wires for button control and the OSD battery indicator one wire for the power supply not needed for touch control. 3 wires for the OSD menu via buttons not needed. Optional A, B and SEL for button control not needed. Wire to the power switch optional, recommended for full brightness

The Q5 XL Laminated and the AMOLED Q10 XL Touch display every Game Boy Color pixel with 16 screen pixels (integer scaling), the 2.45 HD OSD with 9. The picture is not distorted. On the Hispeedido kits and on the RetroPixel you can adjust the picture position, so small misalignments during installation are easy to correct.

On a laminated kit the glass lens is bonded to the screen at the factory. On a non-laminated kit the LCD and the screen lens are two separate parts that you fit one after the other. Both designs have their own use case. Which one suits you mainly depends on your shell and on what you want from the lens.

Laminated: Q5 XL Laminated, AMOLED Q10 XL Touch and RetroPixel Laminated

Section titled “Laminated: Q5 XL Laminated, AMOLED Q10 XL Touch and RetroPixel Laminated”
  • No dust can get between lens and screen during the installation. The installation is quick.
  • You do not need a separate screen lens. The logo sits on the glass lens and is backlit. You can change the colour of the logo lighting.
  • In the Hispeedido USB-C IPS shell set and the FunnyPlaying RetroPixel Q5 shell you drop the screen in without any modification.
  • Original shells and other shells need extensive modification. This takes some skill and we cannot recommend it. RetroSix shells are usually not suitable for laminated kits.

This design suits you if you use a matching IPS ready shell and do not want to fit a lens dust-free yourself.

  • The screen lens is a separate part and comes with both kits. You can swap it later independently of the LCD, for example if you want a different colour.
  • The Q5 XL has a larger viewing area than the original LCD and therefore needs a larger lens. Original lenses would cover a few millimetres of the picture on each side. Matching lenses are the RetroSix IPS Q5 screen lenses.
  • The Q5 XL fits the RetroSix IPS Q5 shells, which are prepared for it. The Hispeedido and FunnyPlaying shells need minor adjustments. In the original shell you remove the ridge at the back and widen the screen window, which is an extensive modification.
  • You fit the 2.45 HD OSD into the original shell or a RetroSix shell without cutting. You can refit the original LCD later.
  • The 2.45 HD OSD has the picture size of the original LCD. Lenses for original-size IPS kits are for example the RetroSix glass screen lenses.
  • When fitting the lens, it is up to you to keep dust out between LCD and lens. Fit the lens as the last step. A dust blower helps.
  • The Q5 XL has a backlit logo. To use it you need a lens with transparent artwork and a transparent shell, or you trim the LCD surround on the inside of the shell.

This design suits you if you want to pick the lens by colour or swap it later. The 2.45 HD OSD also suits you if you want to keep your original shell without cutting.

An IPS ready shell saves you the modification work. Which shell fits depends on the design of the kit. You can find all shells in the Game Boy Color shells category.

Shell Kits that fit without modification Screen lens Battery compartment
Hispeedido USB-C IPS shell set Q5 XL Laminated, AMOLED Q10 XL Touch, RetroPixel Laminated not needed (laminated kits) AA batteries, USB-C battery cover included
FunnyPlaying RetroPixel Q5 shell Q5 XL Laminated, AMOLED Q10 XL Touch, RetroPixel Laminated not needed (laminated kits) AA batteries and most battery mods
RetroSix IPS Q5 shell set Q5 XL (break out small tabs), 2.45 HD OSD, original LCD tempered glass lens included AA batteries and battery mods, CleanJuice without cutting
USB-C Prestige shell set IPS Q5 ready Q5 XL (break out small tabs), 2.45 HD OSD, original LCD tempered glass lens included AA batteries and battery mods, USB-C cut-out for the CleanJuice

This shell is made for the laminated kits. The Q5 XL Laminated, AMOLED Q10 XL Touch and RetroPixel Laminated fit without modification. The non-laminated Q5 XL fits with minor adjustments. The shell is not intended for the original LCD. The set contains buttons, rubber pads, screws, battery contacts and an IR cover, plus a battery cover for AA batteries and a battery cover with a USB-C opening for the Hispeedido USB-C battery. The RetroSix CleanJuice does not fit this shell.

This shell is designed for the laminated kits. The Q5 XL Laminated, AMOLED Q10 XL Touch and RetroPixel Laminated fit without modification. The non-laminated Q5 XL fits with minor adjustments. The shell is not intended for the original LCD. Leave out the middle mainboard screw during assembly, otherwise the front of the shell can warp. Two screws hold the mainboard securely. The RetroSix CleanJuice does not fit because of its battery shape.

RetroSix IPS Q5 shell set and USB-C Prestige shell set

Section titled “RetroSix IPS Q5 shell set and USB-C Prestige shell set”

Both RetroSix sets are prepared for the Q5 XL. You break out a few small tabs (posts) around the screen opening and fit the LCD. [GBC] Trimming RetroSix Shells shows how. The 2.45 HD OSD and the original LCD fit without modification.

How to modify an original shell is shown with pictures in the guide for each kit:

  • Q5 XL Laminated, AMOLED Q10 XL Touch and RetroPixel Laminated: enlarge the screen window and remove the ridge along the full length of the lower edge of the screen opening. Trimming is a lot of work, so we recommend a matching IPS ready shell. Guide
  • Q5 XL: remove the whole ridge at the back of the screen opening, sand the surfaces flat and widen the screen window by 4 to 5 mm on each side. This is an extensive modification. Guide
  • 2.45 HD OSD: the kit has the original size and fits without cutting. You stick the LCD in place with the included double-sided tape. You can refit the original LCD later. Guide
  • A tri-wing screwdriver for the shell screws and a Phillips screwdriver for the board screws. In our shop: 10-in-1 screwdriver set
  • Side cutters to trim the pins of the cartridge slot (not needed for the 2.45 HD OSD)
  • Tweezers for the ribbon cables: ESD tweezers set
  • A dust blower to keep dust off LCD and lens
  • A craft knife and sandpaper if you need to modify a shell
  • A soldering iron for the AMOLED Q10 XL Touch and for the optional wires of the other kits

Test the kit outside the shell before you install it. The Game Boy Color runs on 2 x AA batteries, so 3 V. How do I test the LCD shows how. On the AMOLED Q10 XL Touch you solder the power wire on before the test, without it the screen stays black. You can still make a warranty claim. Kits that have already been installed cannot be returned under warranty. The LCD is fragile: never press on it from behind and do not take it out again once it sits on the adhesive tape.

  • The pins of the cartridge slot can press on the LCD and damage it permanently. Trim them as short as possible with side cutters and wear safety glasses. On the 2.45 HD OSD you do not need to trim the pins.
  • Our guides recommend replacing the 100 µF capacitor with a 680 µF capacitor for a screen mod. A 680 µF capacitor comes with the RetroSix CleanPower.
  1. Take the Game Boy Color apart: [GBC] Shell Disassembly
  2. Test the kit outside the shell
  3. Trim the pins of the cartridge slot (not for the 2.45 HD OSD)
  4. Modify the shell if you are not using a matching IPS ready shell
  5. Install the kit following the guide for your model
Kit Installation guide Shell modification In our shop
Q5 XL Laminated [GBC] Q5 Laminated IPS by Hispeedido [GBC] Trimming the shell View product
AMOLED Q10 XL Touch [GBC] AMOLED XL Touch Kit by Hispeedido [GBC] Trimming the shell View product
Q5 XL [GBC] Installation Q5 IPS [GBC] Trimming the Shell, [GBC] Trimming RetroSix Shells View product
2.45 HD OSD [GBC] Hispeedido 2.45 OSD IPS Kit not needed View product
RetroPixel Laminated [GBC] Installing the FP RetroPixel 2.0 Laminated [GBC] Trimming the shell View product

The guide for the RetroPixel 2.0 Laminated also applies to version 2.1.

How to open the menu after installation:

  • Q5 XL Laminated: you operate the OSD menu with the touch sensors. With the optional wires it also works with the buttons.
  • Q5 XL: a short press on the left touch sensor switches the colour palette, a long press switches the pixel effects. A short press on the right sensor sets the brightness. Once you have soldered the 3 wires, hold SELECT and press A + B to open the OSD menu.
  • AMOLED Q10 XL Touch: touch the lower third of the screen for 5 seconds. To close the menu, touch the screen outside the menu for 3 seconds.
  • 2.45 HD OSD: touch both touch sensors for 5 seconds.
  • RetroPixel Laminated: hold START + SELECT for a few seconds. A long press on the touch sensor switches the pixel effects.

The original voltage regulator of the Game Boy Color is not designed for the current draw of modern screens and is often overloaded by IPS mods. If the console no longer starts after the installation or restarts at full brightness, the RetroSix CleanPower replaces the regulator board. It supplies a stable 5 V, and the included 680 µF capacitor prevents restarts under load. Installation: [GBC] RetroSix CleanPower

  • Random resets, picture faults or a console that does not start can also be caused by aged capacitors. The recap kit for Game Boy Color replaces them.
  • If the connector for the LCD ribbon cable on the mainboard is faulty or worn, replace it with the LCD ribbon connector.
  • If the touch sensors of the Q5 XL trigger constantly or not at all, their cables often run too close to the ribbon cable between board and mainboard. Route them with some distance.
  • If the RetroPixel logo lights up incorrectly, hold START + SELECT for 5 seconds. Repeat until the logo is displayed correctly again.

The Game Boy Color runs on 2 x AA batteries.

Instead of batteries you can fit a rechargeable battery with a USB-C or USB charging port. Which one fits depends on the shell:

Battery Matching shells Original shell
Hispeedido USB-C battery pack with battery cover Hispeedido and FunnyPlaying shells modify the shell
RetroSix CleanJuice USB-C battery pack RetroSix shells without modification, USB-C cut-out in the USB-C Prestige shell set cut out the floor of the battery compartment
FunnyPlaying battery mod RetroSix and FunnyPlaying shells without modification small modification in the battery compartment

The CleanJuice does not fit the Hispeedido or the FunnyPlaying shell. You charge the FunnyPlaying battery mod at 5 V using the included USB cable. USB cables with a built-in 3 V converter are not suitable for this.

On the AMOLED Q10 XL Touch you solder one wire for the power supply, you already need it for the function test. The Q5 XL Laminated, Q5 XL, 2.45 HD OSD and RetroPixel Laminated install without soldering. Optional wires let you operate the menu with the buttons or add functions, such as full brightness on the RetroPixel. We recommend this wire.

Not for the 2.45 HD OSD, it fits the original shell and the RetroSix shells without cutting. For the Q5 XL a RetroSix IPS Q5 shell is the best choice, the original shell needs extensive modification. The laminated kits only fit an original shell with extensive modification. With an IPS ready shell you skip that step.

Not for the laminated kits, the lens already sits on the screen. The Q5 XL and the 2.45 HD OSD come with a glass lens. The RetroSix IPS Q5 shell sets also include a lens.

What is the difference between IPS and AMOLED?

Section titled “What is the difference between IPS and AMOLED?”

The AMOLED Q10 XL Touch shows deep blacks with high contrast. You operate the menu directly on the screen. The IPS kits use a backlight and are operated with touch sensors or buttons.

You can find all screen kits for the Game Boy Color in the Game Boy Color screens category.