Skip to content

Replacing and soldering a game cartridge battery

Many game cartridges store your progress in a small RAM chip (SRAM). This chip only keeps its data as long as it is powered, which is the job of a 3 V lithium coin cell inside the cartridge. In some games the battery also runs a real-time clock, for example in Pokémon Gold, Silver and Crystal or Pokémon Ruby, Sapphire and Emerald.

Most of these batteries have been in the cartridge since the 90s and are weak or empty by now. Typical signs:

  • The game starts, but your save is gone or the game no longer saves.
  • After switching off, the last saved progress is missing.
  • The game reports that the internal battery has run dry, or the in-game clock has stopped.

This page explains which battery you need, how to back up your save first and how to solder in the new battery.

The name of a coin cell tells you its size: CR2025 means 20 mm diameter and 2.5 mm thickness. All types deliver 3 V, they differ in size and capacity.

CR1616 with solder tabs CR2025 with solder tabs CR2032 with solder tabs
Size 16 mm x 1.6 mm 20 mm x 2.5 mm 20 mm x 3.2 mm
Capacity (typical) approx. 55 mAh approx. 165 mAh approx. 220 mAh
Typically found in Game Boy Advance cartridges with a battery, some Game Boy and Game Boy Color cartridges most Game Boy and Game Boy Color cartridges (e.g. Pokémon Red, Gold and Silver) SNES and N64 cartridges

The table shows the usual types. Still go by the marking on your cartridge’s board, because the fitted battery varies by game and board revision.

A CR2032 fits into some Game Boy cartridges in place of the CR2025 and lasts longer thanks to its higher capacity. It is 0.7 mm thicker though, so it sits very tight. If the shell bulges when you screw it shut, use the type printed on the board.

In Pokémon Ruby, Sapphire and Emerald the save is stored in flash memory that needs no battery. The battery only runs the in-game clock. When it is empty you can keep playing and saving, but time-based events in the game no longer happen. Your save stays intact when you replace the battery. Many other GBA games do not use a battery at all.

A multimeter tells you whether the battery really is the problem. Open the cartridge, set the multimeter to DC voltage (V DC) and measure directly at the two battery tabs.

Reading Meaning
approx. 2.8 V or more battery is fine
approx. 2.0 to 2.8 V battery is getting weak, plan a replacement
below approx. 2.0 V save at risk, back it up and replace now

A negative reading means your probes are swapped.

In Game Boy, Game Boy Color, SNES and N64 cartridges with a battery, the save depends directly on the battery. As soon as you lift one tab, it is erased. If you want to keep it, read it out first as a .sav file with a USB cartridge reader and write it back to the cartridge after the swap. If the battery is already dead and the save is gone, you can skip this step.

  • Battery with solder tabs in the right type
  • Screwdriver for the cartridge: 3.8 mm gamebit for Game Boy, Game Boy Color, SNES and N64 cartridges, tri-wing for Game Boy Advance cartridges. Both are included for example in the 10-in-1 screwdriver set.
  • Temperature-controlled soldering iron (approx. 330 to 350 °C) with a fine tip
  • Solder, easiest is leaded electronics solder with a flux core
  • Flux (no-clean) for old, oxidised joints
  • Desoldering wick or desoldering pump
  • Tweezers
  • Side cutters to trim the tabs
  • Isopropyl alcohol and cotton swabs for cleaning
  • Optional: multimeter, Kapton tape for insulation

Remove the screw on the back. On Game Boy and Game Boy Color cartridges, slide the front shell down a few millimetres and lift it off. Take the board out of the shell so you do not melt any plastic while soldering. If the board moves around, hold it in place with a small clamp or a bit of tape on your work surface.

Take a photo of the old battery before you remove it. The board marks the contacts with + and −. On the battery itself, plus is the large flat side with the print, minus is the smaller side.

Put a little flux on both joints. Heat one joint and lift the tab with tweezers as soon as the solder is liquid. Repeat on the second joint. Never pull on the battery while the solder is still solid: the old pads will come off the board and the cartridge will not save at all afterwards.

If the battery is stuck, you can also snip the tabs off right at the battery with side cutters first. The battery is then out of the way and you can desolder the remaining tab pieces one by one. Make sure the cutters never touch both sides of the battery at the same time.

On SNES and N64 cartridges the tabs go through holes in the board and are soldered on the back. Remove the solder there with desoldering wick or a pump until the tabs move freely.

Lay the desoldering wick on the pad and press the hot tip onto it briefly until the wick has soaked up the old solder. Then clean the area with isopropyl alcohol. Clean, flat pads take new solder much better.

Place the new battery on the board as a test and check that the tabs line up with the pads. Battery plus must go to the board’s plus pad.

  • The tabs of a replacement battery often sit differently than on the original. You may have to fit the new battery upside down. That is fine as long as the polarity is correct.
  • Bend the tabs to fit and trim them with side cutters if they are too long.
  • On SNES and N64 cartridges, bend the tabs down, push them through the holes and solder them on the back. On our batteries one of the two tabs is slightly too wide for its hole. Trim it narrower with side cutters until it fits through.
  • The tab on the top side of the battery must not touch the battery’s rim. The rim belongs to the positive terminal, contact would short the battery. The plastic ring around the battery protects against this, so do not damage it.

First tin one pad with a little fresh solder. Place the tab on it, hold it in position with tweezers and heat tab and pad together until the solder flows. Take the iron away after 2 to 3 seconds. Let the joint cool briefly, then solder the second tab.

Never touch the battery body with the iron and do not keep heating one spot for minutes. If a joint does not look right, wait a moment and try again.

  • Does the battery sit firmly without wobbling?
  • Are there any solder bridges to nearby traces or components?
  • With a multimeter you should now read around 3 V at the joints.
  • If the new battery is larger than the old one, put a piece of Kapton tape over it so it cannot touch other contacts.

Put the board back into the shell and screw the cartridge shut. If you backed up your save, write it back with the cartridge reader now. Then test:

  1. Start the game, save and switch the console off.
  2. Remove the cartridge, wait a moment, insert it again.
  3. Switch the console on and check that your save is there.

In Pokémon Gold, Silver and Crystal, set the clock again after the swap. On the title screen, hold Down on the D-pad, SELECT and B at the same time.

  • Taping a regular coin cell in place: the contact is unreliable, adhesive residue attacks the board over time, and tearing off the old tabs often lifts the pads.
  • Soldering tabs onto a regular coin cell: the heat damages the cell. It loses capacity or, in the worst case, leaks or bursts. Always use a battery with factory-welded tabs.
  • Swapped polarity: the cartridge does not save. Check which tab is connected to plus before soldering.
  • Lifted pads: happens when you pull on the battery before the solder is liquid. Rather reheat once more and use flux.
  • Battery too thick: the shell bulges and presses on the board. Use the type printed on the board.

With a socket you only solder once. After that you insert a standard coin cell without tabs and replace it later without a soldering iron. How to fit one is shown in Installing a battery socket in a game cartridge.

A CR1616 has much less capacity than a CR2025. If you replace a CR2025 in a Game Boy cartridge with a socket and a CR1616, you will need to change the battery correspondingly sooner.