Skip to content

Installing a battery socket in a game cartridge

A battery socket replaces the soldered-in save battery in a game cartridge. You solder it in once and then insert a standard coin cell without solder tabs. Next time the battery needs changing, you will not need a soldering iron.

What the battery in a cartridge is for, which type goes into which cartridge and how to replace a tabbed battery is covered in the guide Replacing and soldering a game cartridge battery.

CR1616 socket CR1632 socket
For cartridges of Game Boy, Game Boy Color, Game Boy Advance and others NES, SNES, N64 and others
Battery CR1616 (16 mm x 1.6 mm) CR1632 (16 mm x 3.2 mm)
Battery in our shop CR1616 coin cells in a 5-pack standard size, available separately
Connections flat solder legs that sit on the board’s pads flat solder legs, bend them down and push them through on cartridges with solder holes

Many Game Boy and Game Boy Color cartridges come with a CR2025 of around 165 mAh from the factory. A CR1616 has about 55 mAh. If you fit a CR1616 socket there, the battery will last correspondingly shorter. In return, changing it takes a minute.

A socket is most worthwhile for games you play a lot and for cartridges that drain their battery quickly, such as games with a clock. You can buy fresh coin cells anywhere and know the cell is new when you insert it.

On the other hand, a socket sits a little higher than a soldered battery, and the plastic holders are more delicate. Tight shells, especially Game Boy Advance cartridges, leave little room. If the shell will not close there without pressure, a battery with solder tabs is the better choice.

  • CR1616 socket or CR1632 socket and a matching coin cell
  • Screwdriver for the cartridge: 3.8 mm gamebit for Game Boy, Game Boy Color, SNES and N64 cartridges, tri-wing for Game Boy Advance cartridges, for example from the 10-in-1 screwdriver set
  • Temperature-controlled soldering iron (approx. 330 to 350 °C), solder, flux, desoldering wick
  • Tweezers and side cutters
  • A bit of tape or Kapton tape to hold the socket in place while soldering
  • Isopropyl alcohol and cotton swabs
  • Optional: multimeter

1. Back up your save and open the cartridge

Section titled “1. Back up your save and open the cartridge”

If your save depends on the battery, read it out with a cartridge reader first. Open the cartridge and take the board out of the shell. Both steps are described in more detail in the battery guide.

2. Remove the old battery and clean the pads

Section titled “2. Remove the old battery and clean the pads”

Note where + and − are on the board. Put flux on the joints, heat them and lift the old battery’s tabs with tweezers as soon as the solder is liquid. Old solder often flows poorly: add a little fresh solder so the two mix, then remove it with desoldering wick.

Clean the pads with desoldering wick until they are flat and shiny, and add a little fresh flux.

Put a battery into the socket and hold it on the board. Check:

  • Do both legs reach their pad?
  • Does the shell still close with the battery in place? Game Boy Advance cartridges are especially tight, and depending on the board the socket rests on a chip there.

If a leg does not touch its pad, bend it carefully with tweezers. The legs break easily, so bend them slowly and only as far as needed.

On NES, SNES and N64 cartridges the connections go through solder holes in the board. Bend the legs of the CR1632 socket down by 90° and trim them narrower with side cutters until they fit through the holes.

The battery always goes into the socket with plus facing up. The contact touching the top of the battery is therefore plus, the contact on the floor is minus.

On the CR1616 socket you can spot the negative terminal by the Y-shaped spring in the floor. That leg goes to the board’s − pad, the other one to +.

Take the battery out again before soldering. Hold the socket in position with a piece of tape. Then press one leg onto its pad with the iron tip and feed in solder until leg and pad are cleanly joined. Only touch the socket’s plastic briefly. Let the joint cool and solder the second leg.

On cartridges with solder holes, solder the legs on the back and trim protruding ends with side cutters.

Then remove the tape and clean flux residue off the joints with isopropyl alcohol.

Insert the coin cell with plus facing up. Make sure all retaining clips grip the battery and the top contact sits over the battery.

With a multimeter you should now read around 3 V at the two joints. If it shows nothing, the battery is not seated properly or is upside down.

Put the board into the shell and close it. The shell halves must slide together without pressure. If it jams, open the cartridge again and check that the socket sits flat. If the shell keeps pressing on socket and board, solder joints can crack.

Write your backed-up save back, save in the game, switch off, remove the cartridge and check after reinserting it that your save is still there.

  • Socket soldered in the wrong way round or battery inserted minus up: the cartridge does not save. Nothing gets damaged, you just correct the orientation. Any save made until then is lost though.
  • Broken leg: happens when bending too fast or too far. If needed, bridge the gap to the pad with a short piece of wire.
  • Battery left in the socket while soldering: the heat travels through the contact straight into the cell.
  • Shell forced shut: the pressure rests permanently on socket, chip and solder joints.
  • Battery removed for storage: with a socket that is quick to do, but a save stored in SRAM is lost.